lmsensors

Mit dem ~lmsensors-Addon kann man verschiedene Temperaturen, Spannungen und Lüfterdrehzahlen auslesen.

Eine Liste von unterstützten Chipsätzen ist ~hier zu finden.

Installation:

Datei auf dem Ipcop ins /tmp-Verzeichniss kopieren, mit

tar xfz lmsensors_ipcop_1.4.8.tar.gz

entpacken.
Dann ins lmsensors-Verzeichniss gehen und

./install


aufrufen.

Am Ende des Installtionsvorganges werden noch weitere Hinweise angezeigt, die unbedingt zu beachten sind !!!!

Nach dem Abschluss der Installation hat man im Webinterface unter Dienste ==> lmsensors die Möglichkeit, lmsensors zu aktivieren/deaktivieren und eine Funktion namens healthd einzuschalten (!! Bevor healthd gestartet wird müssen unbedingt die Emaileinstellungen vorgenommen werden !! ).

Healthd läuft als Dienst im Hintergrund und prüft die Werte von lmsensors.
Nachdem healthd gestartet wurde dauert es ca 15-20 Sekunden, bevor er auf der Statusseite als 'Läuft' angezeigt wird.
Sollte lmsensors einen Alarm auslösen, wird eine Email versandt.

Ausserdem kann man auf der lmsensors-Seite noch die Einheiten und Einstellungen für die grafische Auswertung machen.
Hilfe dazu ist ebenfalls auf der lmsensors-Webinterfaceseite zu finden.
Die Werte die auf der Webinterfaceseite für die Graphen eingestellt werden müssen haben nur mit der grafischen Auswertung zu tun, nichts mit der Funktion von lmsensors an sich !

Dann hat man noch unter Status ==> Sensor Graphs eine grafische Anzeige der Temperaturen und Spannungen.


Deinstallation:

Einfach

uninstall_lmsensors

aufrufen, das war's.


Zum Schluss möchte ich mich nochmal bei Shaun Feakes bedanken, der den Teil mit der grafischen Auswertung gemacht hat.






With the ~
lmsensors-Addon you could read temperatures, fanspeed and voltages from your mainboard.

A list of supported chipsets could be found ~here.

Installation:

Copy the file to the /tmp-directory on your ipcop, extract with

tar xfz lmsensors_ipcop_1.4.8.tar.gz

go into the lmsensors-directory and run

./install


At the end of the installation-process you will see some instructions which must be followed !!!!

After installation you could go into the webinterface under services ==> lmsensors and enable/disable lmsensors and a service called healthd (!! Befor starting healthd you have to make your emailsettings !! ).

Healthd is running as a service in the backround and watching lmsensors.
After starting healthd it will take about 15-20 seconds to show healthd as 'running' on the statuspage.
If lmsensors reports an alarm you will receive an email.

On the webinterface you could also to the configuration of the sensor graphs.
Some help is given on the lmsensors-Webinterface.
The graphs-configuration in the webinterface has nothing to do with lmsensors itself, it is only for the sensorgraphs !

Under Status ==> Sensor Graphs you could view the sensorgraphs.


Uninstall:

Just run

uninstall_lmsensors

that's it.


Finally i would like to say 'Thank You very much' to Shaun Feakes , who did all the sonsorgraphs-stuff in this addon.




License/Lizenz: GPL

 

Download lmsensors

 

[Home] [Impressum] [Disclaimer] [Downloads] [Asterisk] [LaBrea Tarpit] [p2pblock] [QoS] [Guardian] [Doorman] [Firewall-Graphs] [vi with colors] [Layer7-Filter] [MC] [lmsensors] [fwlogs] [Sarg] [snortalog] [FAQ]
This site is hosted by
SourceForge.net Logo